Engineering

Design and Construction of 20 Watts Wireless Public Address System

Design and Construction of 20 Watts Wireless Public Address System

ABSTRACT

It has become inevitable that there would be communication and due to the inherent limitation of the human voice, the public address system came to being. A public address or “P.A SYSTEM” is an electronic amplification system with a mixer, amplifier and loudspeakers, used to reinforce a given sound, e.g a person making a speech, pre-recorded music or message and distributing the sound throughout a venue. The voice signal is passed through a microphone, which converts the sound energy to electrical energy, the energy electrical signal being transmitted is been received and amplified by the amplifier circuit. The amplifier’s output is fed into the loudspeaker which converts the electrical energy back to the original form but amplified sound energy. This project is made up of the power supply unit, the pre-amplifier and power amplifier units, and the tone control unit. This system is capable of delivering 20W of electrical power into an 8-ohm load (loudspeaker).

CHAPTER ONE

INTRODUCTION

1.1 BACKGROUND OF THE STUDY

A public address system allows you to broadcast information to a large group of people, whether you are giving a speech or playing live or recorded music.

Public address systems typically consist of input sources, preamplifiers, control and monitoring equipment, and loudspeakers. Input sources refer to the microphones that provide a sound input for the system. These input sources are fed into the preamplifiers. The pre-amplified signals are then passed into the audio power amplifiers.

These amplifiers will amplify the audio signals to an adequate speaker line level. Given the above, one can now say that the public address system is an electronic amplification system used for communication in public areas.

The microphone is a device that converts sound waves into electrical waves. Sometimes colloquially called a micro mike is an acoustic-to-electric transducer or sensor that converts sound into an electrical signal. Microphones are used in many applications such as telephones, hearing aids, life and recorded audio engineering, in radio and television broadcasting and computers for recording voice, and non-acoustic purposes such as ultrasonic checking. The sensitive transducer element of a microphone is called its element. Since a wireless microphone is used in this project; a wireless microphone is one in which communication is not limited by a cable.

A transmitter is extremely important equipment and is housed in the broadcasting station. Its purpose is to produce radio waves for transmission into space. The important components of a transmitter are a microphone, audio amplifiers, oscillator and modulator.

It usually sends its signal using a small FM radio transmitter to a nearby receiver connected to the sound system, but it can also use infrared light if the transmitter and receiver are within the sign of each other. The transmitter is responsible for taking in the signal from the microphone, modulating it, and transmitting it to the receiver using radio waves.

The first transistor (Q1) is the pre-amplifier for the microphone, and you can omit this circuit if you don’t want to transmit the sound picked up by the mic, for example, you can connect your mp3 player directly to C1. The core of this FM transmitter circuit is Q2, a modified Culprits oscillator that the frequency is determined by L1, C4, C6, and the transistor’s internal base-emitter capacitance. The antenna uses 1/16 wavelength to compromise the efficiency and the size. If you want the microphone to be less sensitive, we can replace the R1 with a higher resistor, such as 10k or 22k, and this might overcome the feedback problem if you use this wireless microphone FM transmitter for a public address system.

The receiver captures the radio waves sent out by the transmitter, demodulates the signal, amplifies it to an appropriate level, and sends it out to the audio mixer. A receiver is an electronic circuit that receives its input from an antenna, uses electronic filters to separate a wanted radio signal from all other signals picked up by this antenna, amplifies it to a level suitable for further processing, and finally converts through demodulation and decoding the signal into a form usable for the consumer, such as sound, and digital data, etc.

Amplifier or simply amp is any device that changes, usually increases, the amplitude of a signal. The “signal” is usually voltage or current. The amplifier is a device for increasing the power of a signal. It does this by taking energy from a power supply and controlling the output to match the input signal shape but with a larger amplitude. Routing the low-frequency parts of the signal to an amplifier can substantially improve the clarity of the overall sound reproduction.

In this project, the audio amplifier used is capable of delivering 20watts continuously. The term “power amplifier” is a relative term concerning the amount of power delivered to the load and/or sourced by the supply circuit.

In general, a power amplifier is designated as the last amplifier in a transmission chain (the output stage) and is the amplifier stage that typically requires the most attention to power efficiency. Power amplifiers have also become lighter, smaller, more powerful and more efficient due to the increasing use of Class A amplifiers, which offer significant weight and space savings as well as increased efficiency.

Power amplifier circuits (output stages) are classified as A, B, AB and C for analogue designs, and class D and E for switching designs, based upon the conduction angle or angle of flow, Θ, of the input signal through the output amplifying device, that is, the portion of the input signal cycle during which the amplifying device conducts. The image of the conduction angle is derived from amplifying a sinusoidal signal. (If the device is always on, Θ = 360o.) In this project a class, A amplifier is used because it offers low signal distortion.

The loudspeaker is an electroacoustical transducer that converts an electrical signal to sound. A transducer that turns an electrical signal into sound waves is the functional opposite of a microphone.

Since a conventional speaker is constructed much like a dynamic microphone, (with a diaphragm, coil and magnet), speakers can actually work “in reverse” as microphones. The speaker pushes a medium in accord with the pulsations of an electrical signal, thus causing sound waves to propagate to where they can then be received by the ear. The loudspeaker used in this project is a load of 8 Ohms.

1.2 AIMS AND OBJECTIVES

Public speaking is the process of speaking to a group of people in a structured, deliberate manner intended to inform, influence, or entertain the audience. In public speaking, as in any form of communication, there are five basic elements, often expressed as “who is saying what to whom using what medium with what effects?”(W.Kleitz;2005 pg 134).

The major objective of this project is to design and construct a public address system with relatively unique operational characteristics that are capable of delivering 20 watts of electrical power into an 8 Ohms load (loudspeaker). This will be achieved with adequate tone controls and mixer stages to enable communication or reproduction of speech and recorded music in buildings and institutions.

1.3 JUSTIFICATION

Over the ages, science and technology have been developing with new inventions in various fields; including the increase in modifications on existing technology all gearing towards improving effectiveness and reliability of equipment and achieving to a great degree miniaturization and optimal cost.

This project is backed by my interest in the area of electronics and communication, and having been groomed to a great extent with introductions into the various fields of electrical and electronics engineering, with the knowledge in principles of telecommunications, telecommunication engineering,
basic electronics and lab practice. I chose to combine basic electronics and lab practice. I chose to combine all these ideas in embarking on this project to develop a special system that utilizes all the above-stated knowledge in one system; “the public address system”.

This system makes use of a radio communication system, it utilizes radio frequency to achieve all its set objectives, like data communication in the operation of wireless communication between the transmitter and the receiver.

This system is intended to provide a fast and reliable means of communication in small venues such as school auditoriums, churches, and small bars.

1.4 SCOPE OF THE PROJECT

This system is for public address; it has an estimated power rating of 20watts. For power supplies, it uses a 220/12Vac transformer for the receiver, amplifier and loudspeaker units. It has power On/Off button with volume control.

1.5 SYSTEM BLOCK DIAGRAM

The system is made up of the transmitter which is incorporated in the microphone; and the receiver unit, the tone control and mixer unit, the audio amplifier unit and the loudspeaker.

1.6 PROJECT WORK ORGANISATION

The various stages involved in the development of this project have been properly put into six chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:

Table 1: Project work organization

REFERENCES

  1. Armstrong, E. H. (2008). History of Electrochemistry, Electricity, and Electronics. Eugenii Katz Homepage, the Hebrew University of Jerusalem. . accessed on 10-05-2008.
  2. Atti, L. (2007). Audio Signal Processing and Coding. U.S.A: John Wiley-Interscience.
  3. Beranek, L. (1954). Acoustics. London: Mc-Graw Hill Books.
  4. Boylestad, R., & Nashelsky, R. (1996). Electronic Devices and Circuit Theory, (7th Edition). London: Prentice-Hall College Division.
  5. Dalton, W. M. (1975). The Story of Radio. London: Adam higher.
  6. Dugan, F. (1993). Electronic Communication. New York, U.S.A: Delmar Learning.
  7. Floyd, T. (2004). Electronic Devices. London: Pearson Educational Publications.
  8. Franco, S. (1988). Operational Amplifiers and Analog Integrated Circuits. New York: Mc-Graw Hill Book Co.
  9. Gibilisco, S. (2002). Teach Yourself Electricity and Electronic. New York: Mcgraw Hill Professional.
  10. Great, K. (1990). Advanced Electronics Project. New York: Mc-Graw Hill Book Co.
  11. Horowitz, L., & Hill, W. (1989). The Art of Electronics. London: Cambridge University Press.
  12. Hughes, E. (1996). Electronic Technology, (7th Edition). England: Prentice Hall Harlow.
  13. James, K. M. (2001). Room Reverberation effects in Hearing aid Feedback Cancellation. Journal of the Acoustical Society of America: pp. 367-378
  14. Kleitz, W. (2005). Digital Electronics: A Practical Approach. London: Cambridge University Press.
  15. Kouwenhoven, M. H. L. et al (2003). Structured Electronic Design, Negative-Feedback Amplifiers. Ghana: Kluwer Academic.
  16. Malik, N. R. (1995). Electronic Circuits: Analysis, Simulation, and Design. Englewood Cliffs, New Jersey: Prentice-Hall.
  17. Montoro, C. G., & Schneider, M. C. (2007). MOSFET Modeling for Circuit Analysis & Design. London/Singapore: World Scientific.
  18. Sessler, G. M., & West, J. E. (1962). Self-biased Condenser Microphone with High Capacitance. Journal of the Acoustical Society of America. Pp. 1787-1788
  19. Spencer, R. R., & Ghausi, M. S. (2001). Microelectronic Circuits. Upper Saddle River, New Jersey: Pearson Education/Prentice.
  20. WWW.Electronics4u.com
  21. Theraja, B. L., & Theraja, A. K. (1998). A Textbook of Electrical Technology. New Delhi, India: S.Chand & Company.


Copyright © 2023 Author(s) retain the copyright of this article.
This article is published under the terms of the Creative Commons Attribution License 4.0